Multitech MT200A2W-C1 Uživatelská příručka

MultiConnect™ AW Analog-to-Wireless Converter User Guide

Chapter 1 – Product Description and Specifications 10 MultiConnect AW User Guide LEDs LED Indicators Signal ALL OFF - Unit is off, not registered on

Chapter 1 – Product Description and Specifications MultiConnect AW User Guide 11 Category Description Analog Connection Supports connection speeds up

Chapter 1 – Product Description and Specifications 12 MultiConnect AW User Guide Category Description Serial Command Port Fixed @ 115200bps Analog C

Chapter 1 – Product Description and Specifications MultiConnect AW User Guide 13 MT200A2W-H5 Category Description Standard High Speed Packet Access (

Chapter 1 – Product Description and Specifications 14 MultiConnect AW User Guide Power Multi-Tech Systems, Inc. recommends that you incorporate a 10

Chapter 1 – Product Description and Specifications MultiConnect AW User Guide 15 Power Draw for the MT200A2W-C1 US CELLULAR 800 MHz Input Voltage =9

Chapter 1 – Product Description and Specifications 16 MultiConnect AW User Guide PTCRB Requirements for the Antenna There cannot be any alteration t

Chapter 1 – Product Description and Specifications MultiConnect AW User Guide 17 Command Connector The following table explains the pin functions. E

18 M

Chapter 1 – Product Description and Specifications MultiConnect AW User Guide 19 1. Connect the antenna to the ANT connector on the back of the unit

Copyright and Technical Support 2 MultiConnect AW User Guide MultiConnect™ AW User Guide MT200A2W-G, MT200A2W-C1, MT200A2W-H5 S000504, Revision H C

Chapter 2 – Installation 20 MultiConnect AW User Guide

21 MultiConnect AW User Guide Chapter 3 – Configuring Ports Before you start configuring your MultiConnect unit, establish a wireless network accou

Chapter 3 – Configuring Ports 22 MultiConnect AW User Guide 5. Change the Bits per second to 115200. 6. Click Apply and then click OK. 7. Press

Chapter 3 – Configuring Ports MultiConnect AW User Guide 23 Configuring the Port When you use a terminal emulation program to connect to your MultiC

Chapter 3 – Configuring Ports 24 MultiConnect AW User Guide GPRS Port Options GPRS Network Dependent Option Default Description B) Protocol TCPClien

Chapter 3 – Configuring Ports MultiConnect AW User Guide 25 2. Enter 2 for GSM. The GSM Cellular Port menu displays. 3. Set the port options as de

Chapter 3 – Configuring Ports 26 MultiConnect AW User Guide CDMA Cellular Port Configuration 1. Enter 1 for Cellular Port. CDMA is the default for

27 MultiConnect AW User Guide Chapter 4 – Device Configuration Introduction Menu Use Introduction Menu to configure your device, upgrade firmware wi

Chapter 4 – Device Configuration 28 MultiConnect AW User Guide Device Configuration The Main Menu lists configuration and navigation options. Navig

Chapter 4 – Device Configuration MultiConnect AW User Guide 29 GPRS Cellular Port Configuration Network Dependent Option Default Description A) GPRS

Contents MultiConnect AW User Guide 3 Contents Chapter 1 – Product Overview ...

Chapter 4 – Device Configuration 30 MultiConnect AW User Guide G) Remote IP None Remote IP is the IP address of the device you are connecting to for

Chapter 4 – Device Configuration MultiConnect AW User Guide 31 characters that belong to the payload must be sent by the host on the serial port prec

Chapter 4 – Device Configuration 32 MultiConnect AW User Guide GSM Cellular Port Configuration Network Dependent Option Default Description A) GPRS

Chapter 4 – Device Configuration MultiConnect AW User Guide 33 CDMA Cellular Port Configuration Network Dependent Option Default Description A) CDMA

Chapter 4 – Device Configuration 34 MultiConnect AW User Guide J) View or change Phone Number/IP Conversion Table This option allows for additional

Chapter 4 – Device Configuration MultiConnect AW User Guide 35 Option Default Description Modem Initialization String “ “ Allows you to enter initia

Chapter 4 – Device Configuration 36 MultiConnect AW User Guide Option Default Description/Options E) Flow Control RTS/CTS Options are: A) RTS/CTS

Chapter 4 – Device Configuration MultiConnect AW User Guide 37 Timers Option Default Description A) Menu Inactivity Timer 30 (sec) Enter, in seconds

Chapter 4 – Device Configuration 38 MultiConnect AW User Guide System Reboot To reboot the system: ● Enter Y or yes. Enable Debug To turn on debu

39 MultiConnect AW User Guide Chapter 5 – Upgrading Firmware Your device is controlled by semi-permanent firmware, which is stored in flash memory.

Contents 4 MultiConnect AW User Guide Configuring the Port ...

Chapter 5 – Firmware Upgrade 40 MultiConnect AW User Guide Identifying the COM port 1. Go to Start I Control Panel and then Open Device Manager.

Chapter 5 – Firmware Upgrade MultiConnect AW User Guide 41 3. Close the terminal program. 4. Double-click the Flash Wizard icon or filename to ru

Chapter 5 – Firmware Upgrade 42 MultiConnect AW User Guide 7. When the flash upgrade is complete, Programming Complete appears. 8. Click Next. T

43 MultiConnect AW User Guide Chapter 6 – Configuration Scripts The following are example scripts you can use to configure a MultiConnect through a

Chapter 6 – Configuration Scripts 44 MultiConnect AW User Guide sendln "yes" wait 'ConfigMenuScript' pause 1 ;--------------

Chapter 6 – Configuration Scripts MultiConnect AW User Guide 45 pause 1 ; sendln "1 L ???" ; for the last parameter: Enter the APN

Chapter 6 – Configuration Scripts 46 MultiConnect AW User Guide ; pause 1 ; sendln "2 B E RTS_CTS" ; Choices for the last param

Chapter 6 – Configuration Scripts MultiConnect AW User Guide 47 ;------------------------------------------------------------------------------------

Chapter 6 – Configuration Scripts 48 MultiConnect AW User Guide pause 1 sendln "C" wait 'Are you sure you want to start the confi

Chapter 6 – Configuration Scripts MultiConnect AW User Guide 49 ; wait 'OK' ; "12000", "9600", "48

Contents MultiConnect AW User Guide 5 REACH Statement ...

Chapter 6 – Configuration Scripts 50 MultiConnect AW User Guide ; wait 'OK' ; sendln "5 E ?????" ; Choice for th

51 MultiConnect AW User Guide Chapter 7 – Troubleshooting Flashing Signal Strength LEDs Flashing signal strength LEDs indicate a failure condition h

Appendix A – Regulatory Compliance 52 MultiConnect AW User Guide Appendix A – Regulatory Compliance EMC, Safety, and R&TTE Directive Compliance

Appendix A – Regulatory Compliance MultiConnect AW User Guide 53 Industry Canada This Class B digital apparatus meets all requirements of the Canadia

54 MultiConnect AW User Guide REACH Statement Registration of Substances After careful review of the legislation and specifically the definition of

Appendix B – Environmental Information MultiConnect AW User Guide 55 Restriction of the Use of Hazardous Substances (RoHS) Multi-Tech Systems, Inc.

Appendix B – Environmental Information 56 MultiConnect AW User Guide Information on HS/TS Substances According to Chinese Standards In accordance wi

Appendix B – Environmental Information MultiConnect AW User Guide 57 Information on HS/TS Substances According to Chinese Standards (in Chinese) 依照中国

6

Chapter 1 – Product Description and Specifications MultiConnect AW User Guide 7 AT Command Information The AT commands for the MultiConnect AW are pu

Chapter 1 – Product Description and Specifications 8 MultiConnect AW User Guide ● Éteignez votre appareil sans fil dans un avion. Utilisant des dis

Chapter 1 – Product Description and Specifications MultiConnect AW User Guide 9 Device Maintenance To maintain the MultiConnect: ● Do not attempt to